1 QS-210/220

1.1 Connecting "C" with "B"

Image: qs-sb2_type_c_b_adapters.png

Image: qs-sb2_type_c_b_diagram.png

Image: type_b_to_motion-lock_r3.png

1. Disconnect old 2-pin Motion Lock switch, it won't be needed anymore.
2. Connect new 6-pin QS-SBML-1 R3 Motion Lock switch into the ML UP port in the Type C power cabinet.
3. If you have second Type C power cabinet, then connect it to the first Type C using its standard wire harness - refer to the interconnections scheme in the original user manual.
4. Connect one end (4-pins) of Motion Lock INTERLINK cable to the ML DOWN port in the Type C power cabinet.
5. Connect another end (6-pins) of Motion Lock INTERLINK cable to QS-SBML-622 adapter.
6. Connect another end (2-pins) of QS-SBML-622 adapter to ML UP port in the Type B power cabinet.
7. If you have yet another Type B power cabinet (2 in total), then connect it to Type B using its standard wire harness - refer to the interconnections scheme in the original user manual.
8. Connect M-BUS cables and M10 in the order of your selection - it does not matter where the bus starts and ends.
9. Plug M-BUS terminator into empty M-BUS port.
10. Plug in the power cables with adequate plugs into power sockets.
11. Set the appropriate position on the CFG switch according to the actuators layout of your choice (more information about CFG switch position and layout selection can be found in the original user manual).

1.2 Connecting "C" with "A"

Image: qs-sbml-62g.png

Image: qs-sbml-1_r3.png

Image: qs-sb2_type_c_a_diagram.png

Image: type_a_to_motion-lock_r3.png

1. Disconnect old 2-pin Motion Lock switch, it won't be needed anymore.
2. Connect new 6-pin QS-SBML-1 R3 Motion Lock switch into the ML UP port in the Type C power cabinet.
3. If you have second Type C power cabinet, then connect it to the first Type C using its standard wire harness - refer to the interconnections scheme in the original user manual.
4. Connect one end (4-pins) of Motion Lock INTERLINK cable to the ML DOWN port in the Type C power cabinet.
5. Connect another end (6-pins) of Motion Lock INTERLINK cable to QS-SBML-62G adapter.
6. Connect another end (2-pins) of QS-SBML-62G adapter to ML UP port in the Type A power cabinet.
7. If you have yet another Type A power cabinet (2 in total), then connect it to Type A using its standard harness - refer to the interconnections scheme in the original user manual.
8. Connect M-BUS cables and M10 in the order of your selection - it does not matter where the bus start and ends.
9. Plug M-BUS terminator into empty M-BUS port.
10. Plug in the power cables with adequate plugs into power sockets.
11. Set the appropriate position on the CFG switch according to the actuators layout of your choice (more information about CFG switch position and layout selection can be found in the original user manual).

1.3 Connecting "A" with "B"

Image: qs-sbml-u2g.png

Image: type_a_to_b_powercabinet.png

1. Connect a 2-pin Motion Lock switch into the ML UP port in the Type A power cabinet per original user manual.
2. If you have second Type A power cabinet, then connect it to the first Type A using its standard wire harness - refer to the interconnections scheme in the original user manual.
3. Connect one end of Motion Lock Interlink Cable to the ML DN port in the last Type A power cabinet.
4. Connect another end of Motion Lock Interlink Cable to the matching QS-SBML-U2G adapter plug.
5. Connect another end (2-pin black) of QS-SBML-U2G adapter to ML UP port in the Type B power cabinet.
6. If you have another Type B power cabinet (2 in total), then connect it to Type B using its standard harness - refer to the interconnections scheme in the original user manual.
7. Connect M-BUS cables and M10 in the order of your selection - it does not matter where the bus start and ends.
8. Plug M-BUS terminator into empty M-BUS port.
9. Plug in the power cables with adequate plugs into power sockets.
10. Set the appropriate position on the CFG switch according to the actuators layout of your choice (more information about CFG switch position and layout selection can be found in the original user manual).

2 QS-BT1/QS-H13 and QS-210/220

2.1 Connecting "C" with "B"

Image: qs-sbml-622.png

Image: qs-sbml-1_r3.png

Image: type_c_to_type_b_h13_bt1.png

Info

In case of connecting only QS-H13 or QS-BT1:

Image: type_c_to_type_b_a_h13_bt1.png

1. Connect 6-pin QS-SBML-1 R3 Motion Lock button into the matching 6-pin port in the QS-BT1 or QS-H13 (order of connection is irrelevant).
2. Connect one end (4-pins) of Motion Lock INTERLINK cable to the matching 4-pin port in the QS-BT1 or QS-H13.
3. Connect another end (6-pins) of Motion Lock INTERLINK cable to 6-pin connector of QS-SBML-622 adapter.
4. Connect the connector (2-pins) of QS-SBML-622 adapter to ML UP port in the Type B power cabinet.
5. If you have another Type B power cabinet (2 in total), then connect it to Type B using its standard wire harness - refer to the interconnections scheme in the original user manual.
6. Connect M-BUS cables and M10 to your power cabinets in the order of your selection - it does not matter where the bus start and ends. QS-BT1 works separately via USB cable.
7. Plug M-BUS terminator into empty M-BUS port in power cabinet.
8. Plug in the power cables with adequate plugs into power sockets.
9. Set the appropriate position on the CFG switch of power cabinet according to the actuators layout of your choice (more information about CFG switch position and layout selection can be found in the original user manual).

2.2 Connecting "C" with "A"

Image: qs-sbml-62g.png

Image: qs-sbml-1_r3.png

Image: type_c_to_type_a_h13_bt1.png

Info

In case of connecting only QS-H13 or QS-BT1:

Image: type_c_to_type_b_a_h13_bt1.png

1. Connect 6-pin QS-SBML-1 R3 Motion Lock button into the ML UP port in the QS-BT1 or QS-H13 (order of connection is irrelevant).
2. Connect one end (4-pins) of Motion Lock INTERLINK cable to the ML DOWN port in the QS-BT1 or QS-H13.
3. Connect another end (6-pins) of Motion Lock INTERLINK cable to 6-pin connector of QS-SBML-62G adapter.
4. Connect the green connector (2-pins) of QS-SBML-62G adapter to ML UP port in the Type A power cabinet.
5. If you have another Type A power cabinet (2 in total), then connect it to Type A using its standard wire harness - refer to the interconnections scheme in the original user manual.
6. Connect M-BUS cables and M10 to your power cabinets in the order of your selection - it does not matter where the bus start and ends. QS-BT1 works separately via USB cable.
7. Plug M-BUS terminator into empty M-BUS port in power cabinet.
8. Plug in the power cables with adequate plugs into power sockets.
9. Set the appropriate position on the CFG switch of power cabinet according to the actuators layout of your choice (more information about CFG switch position and layout selection can be found in the original user manual).

3 DIP switches configuration